Kegland Cold Plate

คุณสมบัติสินค้า:

Specifications - Size: 26cm x 38cm x 2.5cm Thick - 6.5kg Aluminium Casting with large thermal mass

Share

Made from a thick cast aluminium this plate acts as a large heatsink to absorb heat efficiently from your beer.

This new design of cold plate is made from high conductivity aluminium alloy to aid the heat transfer. In addition to this the new cold plates are made with ribs to aid faster heat transfer. - Inside the casting contains 2 x 304 stainless product lines which are 5.5 meters long and 4mm ID.

The inlets and outlets on the cold plate are the standard mfl threads so they are compatible with the wide range of other fittings that we sell such as swivel nut and barbs or the duotight fittings. You can purchase these separately using the links below. - Swivel Nut and Barb ,Duotight FFL to 8mm Push in Fitting.

Usage Instructions:

1. Place the cold plate into your cooler box, esky or ice well.  If you want to stop the cold plate from moving around then use some polyurethane based glue/sikaflex and this will enable you to stick the cold plate down.
2. Fill the esky/cooler box with ice.  Cold plates require the ice to be in contact with the aluminium casting directly so you MUST drain off the water in order for these cold plates to work optimally.  (this is different to cooling coils that require and ice water slurry).
3. Set your keg pressure at 20-30psi.

Troubleshooting: If you get frothing it will generally be caused by one of two things which are easy to solve:

1. If you look at the beer line between the cold plate and your keg (before the beer has gone into the cold plate) and you have bubbles or air pockets in your beer line then your dispence pressure is too low.  Increase your pressure at the keg to ensure the CO2 is not coming out of solution.

2. If you measure the measure the temperature of the beverage as it comes out of the tap it should be below 5C.  If the temperature is higher than 5C then:
a) Make sure you have complete coverage of ice in the eksy/cooler box
b) Decrease the flow rate of product through the cold plate so you the beverage has more contact time as it passes through the cold plate.
c) Over Carbonation WARNING:
As these cold plated require considerable dispense pressures (20-30psi) your beer will gradually absorb more carbonation if you are using pure CO2 to dispense the beer especially if your kegs are cold.  If you are using CO2 to dispense your keg it will work fine for short periods up to 6-7 hours.  If however you cease dispensing then disconnect the kegs and take the additional CO2 out of the head space of the keg before storing the keg.  This will prevent additional CO2 absorbing into solution.  If you are dispensing the kegs over multiple days we would recommend the use of nitrogen/CO2 mixed gas or straight nitrogen and this will prevent any over carbonation of your beer.

ผลิตจากอะลูมิเนียมหล่ออย่างหนาแผ่นนี้ทำหน้าที่เป็นซิงค์ขนาดใหญ่เพื่อดูดซับความร้อนจากเบียร์ของคุณได้อย่างมีประสิทธิภาพ.

แผ่นทำความเย็นดีไซน์ใหม่นี้ทำมาจากโลหะผสมอะลูมิเนียมที่มีค่าการนำไฟฟ้าสูงเพื่อช่วยถ่ายเทความร้อน นอกจากนี้ แผ่นทำความเย็นแบบใหม่ยังทำจากซี่โครงเพื่อช่วยให้ถ่ายเทความร้อนได้เร็วยิ่งขึ้น - ภายในหล่อประกอบด้วยสายผลิตภัณฑ์สแตนเลส 2 x 304 ยาว 5.5 เมตร หนา 4 มม.

ทางเข้าและทางออกบนแผ่นเย็นเป็นเกลียว mfl มาตรฐาน ดังนั้นจึงเข้ากันได้กับอุปกรณ์อื่น ๆ ที่เราจำหน่ายมากมาย เช่น น็อตหมุนและหนาม หรือข้อต่อแบบสองด้าน คุณสามารถซื้อแยกต่างหากได้ทั้ง น็อตหมุนและเข็ม ,Duotight FFL ถึง 8mm Push in Fitting.

คำแนะนำการใช้งาน:

1. วางแผ่นประคบเย็นลงในกล่องแช่เย็น แช่น้ำแข็ง หรือบ่อน้ำแข็ง หากคุณต้องการหยุดการเคลื่อนที่ของเพลทเย็น ให้ใช้กาวโพลียูรีเทน/ซิก้าเฟล็กซ์ ซึ่งจะช่วยให้คุณติดเพลทเย็นลงได้
2. เติมน้ำแข็งในช่อง esky/cooler แผ่นทำความเย็นต้องการให้น้ำแข็งสัมผัสกับการหล่ออลูมิเนียมโดยตรง ดังนั้นคุณต้องระบายน้ำออกเพื่อให้แผ่นเย็นเหล่านี้ทำงานได้อย่างเต็มประสิทธิภาพ (ซึ่งต่างจากคอยล์เย็นที่ต้องการและสารละลายน้ำแข็ง)
3. ตั้งแรงดันถังของคุณที่ 20-30 psi

การแก้ไขปัญหา: หากเกิดฟอง โดยทั่วไปจะเกิดจากหนึ่งในสองสิ่งที่แก้ไขได้ง่าย:

1. หากคุณดูที่เส้นเบียร์ระหว่างแผ่นเย็นกับถังของคุณ (ก่อนที่เบียร์จะเข้าไปในแผ่นเย็น) และคุณมีฟองอากาศหรือช่องอากาศในท่อเบียร์ แสดงว่าแรงดันการจ่ายของคุณต่ำเกินไป เพิ่มแรงดันของคุณที่ถังเพื่อให้แน่ใจว่าไม่มี CO2 ออกมาจากสารละลาย.

2. หากคุณวัดอุณหภูมิของเครื่องดื่มเมื่อออกจากก๊อกก็ควรต่ำกว่า 5C หากอุณหภูมิสูงกว่า 5C แสดงว่า:
a) ตรวจสอบให้แน่ใจว่าคุณมีน้ำแข็งปกคลุมอย่างสมบูรณ์ในกล่อง eksy/cooler
b) ลดอัตราการไหลของผลิตภัณฑ์ผ่านแผ่นทำความเย็นเพื่อให้คุณดื่มมีเวลาสัมผัสมากขึ้นเมื่อผ่านแผ่นเย็น
c) คำเตือนเกี่ยวกับคาร์บอนไดออกไซด์:
เนื่องจากการชุบเย็นเหล่านี้ต้องใช้แรงกดมาก (20-30 psi) เบียร์ของคุณจะค่อยๆ ดูดซับคาร์บอนไดออกไซด์มากขึ้น หากคุณใช้ CO2 บริสุทธิ์ในการจ่ายเบียร์ โดยเฉพาะอย่างยิ่งถ้าถังของคุณเย็น หากคุณกำลังใช้ CO2 เพื่อจ่ายถังของคุณ มันจะทำงานได้ดีในช่วงเวลาสั้น ๆ ถึง 6-7 ชั่วโมง อย่างไรก็ตาม หากคุณหยุดจ่ายยา ให้ถอดถังออกและนำ CO2 เพิ่มเติมออกจากพื้นที่ส่วนหัวของถังก่อนเก็บถัง สิ่งนี้จะป้องกันไม่ให้ CO2 เพิ่มเติมดูดซับลงในสารละลาย หากคุณกำลังจ่ายถังเป็นเวลาหลายวัน เราขอแนะนำให้ใช้ก๊าซผสมไนโตรเจน/CO2 หรือไนโตรเจนแบบตรง ซึ่งจะป้องกันไม่ให้เบียร์ของคุณเกิดคาร์บอนไดออกไซด์มากเกินไป.

Powered by MakeWebEasy.com
เว็บไซต์นี้มีการใช้งานคุกกี้ เพื่อเพิ่มประสิทธิภาพและประสบการณ์ที่ดีในการใช้งานเว็บไซต์ของท่าน ท่านสามารถอ่านรายละเอียดเพิ่มเติมได้ที่ นโยบายความเป็นส่วนตัว  และ  นโยบายคุกกี้