ถังหมักเบียร์และอุปกรณ์เสริม

This easy to use and compact Spunding valve is handy for keg transfers or pressurized fermentations when you want to limit oxygen exposure and use counter pressure in the keg you are filling into or in the fermenter you are using. This new improved G2 model has several upgrades:

A number of our customers wanted something to look better than 2 x Triple Tap Font Series X Plus Allstar Pack.

Kegland FermZilla - Tri-Conical - 600ml COLLECTION (Tri Clover CLAMP, และ Seal)

If the green light does not flash green (captive portal open), it means your battery is insufficiently charged. Leave your pill on the charging pad (not included in this kit) for 24 hours or until it is fully charged (red light turns off). Then lift the Pill on and off the charging pad and it will activate the captive portal (green light will start to flash)

FermZilla Conical - 55L Jacket This jacket is designed to insulate your FermZilla during the colder months to keep your fermentation at the optimun temperature. It can also be used with a heating belt/wrap to warm up the wort if the heat from the fermentation isn't enough. Also completely blocks any light/UV to prevent light stuck beer. To see the video on this product look below:

duotight 8mm Push In Joiner (Double O-Ring)

duotight - 6.5mm (1/4") x 9.5mm (3/8") Reducer This reducer is suitable for our EVABarrier Beer & Gas hosing in 9.5mm (3/8") OD line to 6.5mm (1/4") OD Hosing.

Charge your Pill wirelessly with this easy-to-install upgrade kit from KegLand. The RAPT Pill is a Wifi & Bluetooth hydrometer for logging fermentation to the cloud.

0-15psi

FermZilla 27 L Tri-Conical Starter Kit Gen 3.2

FermZilla 55 L Tri-Conical Starter Kit Gen 3.2

ในชุดจะมี 1. FermZilla Tri-Conical - 3 Inch x 3 Inch Tri-Clover Butterfly Valve 2.FermZilla 600ml Collection Container with 3 Inch Tri-Clover Kit

duotight - 8mm (5/16) x One way check valve This very handy fitting could save you your regulator and is a good investment. This particular type of check valve has low opening pressure of only 1psi. This check valve is suitable for clean liquids such as water or for gas. The spring and internal components are made with stainless steel and quality EPDM seals. This fitting is ideally used with EVABarrier 5mm x 8mm or EVABarrier 4mm x 8mm

Series X ตัวตู้เย็น, ล้อ, ถาด, ที่แขวน co2

kegerator Series X Plus เหมาะสำหรับคิวเวตต์มากถึง 8 ถัง หรือ ถัง 2 ถัง ดัดแปลงให้พอดีกับแท่นวางก๊อก 2 อัน

ชุดลูกลอย พร้อมสาย 80 cm. + กรอง FermZilla

ชุดถ่ายน้ำเบียร์ ในชุดประกอบด้วย 1. duotight 8 mm (5/16) x Ball Lock Disconnect (Black + Yellow/Liquid) 2 ชิ้น 2. สายเบียร์/แก๊ส EVABarrier 5 มม. x 8 mm(5/16) double Wall ยาว 1.5 เมตร

Looking for high quality push in fittings that will seal tight? duotight are the push in fitting with superior sealing capacity

Ice bank comes as standard with 4 built-in submersible pumps each with independent digital controllers allowing the optimum fermentation

The new and improved FermZilla 55L brought to you by the critical key minds and engineers behind the original Gen1.

ntroducing the Gen3 FermZilla Tr-Conical. Now with 3 Inch Tri-Clover ferrule molded into the tank and redesigned tri-clover dump valve.

This RAPT (พร้อมหัวแปลงเสียบปลั๊กไทยได้ 2 ชิ้น) wifi connected temperature controller box will enable you to monitor, track and control heating and cooling devices remotely through the internet. Set complex temperature profiles so the temperature will automatically change over time.

ในชุดประกอบด้วย - hop bong 2" - Butterfly Values 2" to 3" - ฝาแบบใหม่สำหรับต่อ butterfly value และ hop bong - Clamp 2" 3 ชิ้น - gasket 2" 3 ชิ้น - Release value 1 ชิ้น (ไม่มี Carbonation Cap ให้)

เลือกสีได้และมีกล่อง The RAPT Pill allows accurate and precise, true real-time specific gravity and temperature logging and control via wifi/bluetooth

Pills 2 ชิ้น ราคาพิเศษ 2,700 บาท เท่านั้น

If you want an easy way to balance your beer lines this is the way to do it. Please be aware that even in the fully open position these FC disconnects do have some inherent flow resistance so you should use either shorter line or larger ID line that you would when compared with traditional ball lock disconnects. One of the benefits of FC disconnects is you don't need to rely on the small ID or line length to apply flow resistance so it would not make sense to use long lines or small ID lines as well as this is the job of the FC device. This is perfect for people who want to serve a large range of beverages with differing carbonation levels as it gives you the ability to adjust resistance easily. Now with the added benefit of duotight fittings built in. This particular ball lock disconnect has been designed to suit 8mm Beer Line. Due to the integrated duotight fitting the line will simply push directly into this fitting. For this ball lock disconnect we recommend using either: EVABarrier 4mm ID x 8mm OD Line (Best for short draw systems such as our kegerators) or EVABarrier 5mm ID x 8mm ID Line

duotight - 9.5mm (3/8") Check Valve (Gas) This elbow piece is suitable for our EVABarrier Beer & Gas hosing in 9.5mm (3/8") OD line to 6.5mm (1/4") OD. Due to the fact that this check valve cannot be taken apart to clean, we do not recommend it to be used with liquid. duotight 1.10 Design Revision No clamps necessary! We do recommend cutting your hosing straight, not on an angle, to ensure the line has a complete seal. To remove the fitting simply push in the collet and the hose can be removed. These push in fittings are suitable to be used up to 100 psi These push in fittings have been engineered for maximised performance in both gas and liquid applications. Compared to other push in fittings on the market, duotight takes the double safety approach to all of the connections with two EPDM o-rings per hose port. No other push ins on the market have EPDM o-rings, let alone two! per push in connection. What is EPDM? EPDM = Ethylene Propylene Rubber which has excellent chemical resistance including being compatible with ozone, oils, wide variety of alkaline and acid compounds, water, alcohol, ketone and beverages. EPDM is also resistant to aging, weather and will not perish easily like other rubber compounds. When compared with silicon and vinyl EPDM has better gas transmission rates, better wear resistance, is BPA free and is the number one choice for many long lasting food grade applications.

Cornelius Keg Lid Pressure Relief Valve (PRV) A replacement pull-ring style relief valve for your Corny Keg but they are compatible with other products such as the MK4 Regulator and Kegmenter lids. This is the most common relief valve on all ball lock kegs. If you do have a lever tab second hand ball lock keg, you can switch it out with one of these. All of KegLand Brand New Kegs come with a ring pull PRV like this. We supply 3 different pressure relief valve types that differer in opening pressure: RED - 35psi (2.5Bar) GREE - 65psi (4.5Bar) GREY - 100psi (6.9Bar) Max. pressure rating: 35psi NOTE: This is a safety device designed to release pressure at the approximate rated pressure. THIS IS NOT TO BE USED AS SPUNDING VALVE. The pressure rating on these is approximate with tolerance of +/- 10psi. If you need accurate pressure control to hold residual pressure in a pressure fermenter or pressure vessel we would recommend using the BlowTie or alternatively you can get the whole BlowTie Kit.

Cornelius Keg Lid Pressure Relief Valve (PRV) A replacement pull-ring style relief valve for your Corny Keg but they are compatible with other products such as the MK4 Regulator and Kegmenter lids. This is the most common relief valve on all ball lock kegs. If you do have a lever tab second hand ball lock keg, you can switch it out with one of these. All of KegLand Brand New Kegs come with a ring pull PRV like this. We supply 3 different pressure relief valve types that differer in opening pressure: RED - 35psi (2.5Bar) GREE - 65psi (4.5Bar) GREY - 100psi (6.9Bar) Max. pressure rating: 35psi NOTE: This is a safety device designed to release pressure at the approximate rated pressure. THIS IS NOT TO BE USED AS SPUNDING VALVE. The pressure rating on these is approximate with tolerance of +/- 10psi. If you need accurate pressure control to hold residual pressure in a pressure fermenter or pressure vessel we would recommend using the BlowTie or alternatively you can get the whole BlowTie Kit.